Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Are you currently in search of tips around Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can relocate easily; if you have to open a wall surface to remove the old tub as well as place the new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. Rather than hiring a professional to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your washroom if you have actually currently bought a new tub and don't need to alter the plan of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Planning for the Setup
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before carrying on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Utilizing the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub must wait up until the bathtub has been used at the very least when as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on How to Install a Bathtub Yourself. Thanks so much for spending some time to browse our piece. Loved our posting? Please share it. Help other people find it. Many thanks for going through it.
Book-Now
Report this page